HOME T-CASE DRIVESHAFT DIFFERENTIAL MANUAL TRANS ABOUT US

K&L Unlimited 800-662-9103

GM 10bolt 7.5/7.625 Rear Differrntial

Camero,Trans-Am/S-10,GMC/Astro,Bravada see ID to identify other applications.

Jump To Another G.M.Differential


Click on illistration number for description....call for availibility

gendiffexplode.jpg

28 Installation Kit


axle shaft axle c-clip wheel stud axle seal axle bearing pinion nut pinion yoke washer pinion yoke yoke flinger pinion seal outter pinion bearing/race vent fill plug crush sleeve inner pinion bearing /race pinion shim pinion ring gear carrier side shim lock screw cross shaft cover gasket diff cover cover bolt ring gear bolt carrier side shim carrier side bearing diff carrier carrier side bearing inner diff kit


  1. Axleshaft axleshaft.jpg


    Click for application list if your axle is not listed call us we can get most axles made to order.Most of our axles do not come with studs so if you need them don't forget to ask. What about the axle bearing and seal?

    Axles come in 26 and 28 splines
    Measuremets are from face of flange to end


  2. C-Clip

    In most cases if you need one you either lost it or you had a bad axle failure


  3. Wheel Stud

    Sometimes we can help, length and thread is needed we can't always go by application


  4. Axle Seal

    If your seal is leaking don't forget to check your axle for damage.

    Application is needed their are a few choices and an axle code will help off the paper tag on axle tube



  5. Axle bearing and seal   NOTE:Axle bearings and seals are not included in                                                                     installation kit
  6. Axle Bearing

    If you have bad axle bearing also check your axle it could be bad also. Remember to get the axle seal you will have to remove it to replace the bearing.


  7. Pinion Nut

    A new nut is always a good choice to maintain proper torque and the also comes in the instalation kit.


  8. Yoke Washer

    The washer is very important when trying to achieve and maintain nut torque.


  9. Pinion Yoke Yokes on you

    Often the pinion yoke my have to be replaced for various reasons and proper identification is necessary by application or by dimensional measurements. A new seal and crush sleeve is always recomended when changing the yoke.

  10. Yoke Flinger

    Somtimes we can you help on these please call for availability.


  11. Pinion Seal Pinion Yoke nut and seal

    Got to keep the oil in, this seal is also included in the
    instalation kit a new crush sleeve and nut is also recomended.

  12. Outter Pinion Bearing/Race

    This bearing is included in the
    installation kit


  13. Vent

    If you need one let us know if it is press in or threaded. Make sure your vent is not plugged if the differential can not breathe the oil will be fourced out through the seals.If oil is comming out of the vent chances the vehicle is upside down or the unit has been overfilled.


  14. Fill Plug

    Did you strip out the plug? You can't get oil in if you can't get it out or did you loose it? Got to have one in or oil will come out! Let us know if you need one.

  15. Crush Sleeve

    This is also included in the
    installation kit and a very important part when installing a ring and pinion to maintain proper pinion bearing pre-load. It is also good to install a new one when ever you remove the pinion nut.


  16. Inner Pinion Bearing/Race

    This bearing and race is included in the
    installation kit


  17. Pinion Shim

    pinion depth shims are required when installing a new ring and pinion to achieve the proper tooth contact pattern.


  18. Ring And Pinion Sets

     ringpinion.jpg Click
    here for available ratios
    Need to know how to figure gear ratio click here


  19. Lock Screw

    It is common for these lock screws to break when removing the cross shaft to to remove the axles.


  20. Carrier Shims

    Shims are required when installing a ring and pinion to set correct backlash.The shims we carry a called Super Shims click
    here to find out why thay are so super.


  21. Carrier Side BearingThese bearings and races are included in the bearing installation installation kit

  22. Differential Carrier
    opencasebare.jpg Open Bare case
    auburn.jpg auburnimg.jpg  
    Limited Slip We have had very good luck with these units.

  23. Ring Gear Bolt

  24. Cross Shaft

  25. Cover Gasket

  26. Differiental Cover

  27. Cover Bolt

  28. Inner Defferential Kit

  29. Installation Kitdiffbrgkit.jpg


    What better than a kit to aid in your ring and pinion install or simple rebuild .......
    info

diffbrgkit.jpg

Complete installation kit

1982 and up Kit info
Note:Axle bearings and seals
sold sepperatly.....see axle shafts

Super Shims

For carrier bearing
preload and backlash


Click for available ratios

RING AND PINIONS

ringpinion.jpg

Pinon Yokes

pinionyoke.jpg

Pinion Yoke
Install Kit

pinionyokekit.jpg

Includes yoke,
seal,nut and
crush sleeve

Limited Slip And Open Differential Related Parts

Auburn

auburn.jpg

Click for Listing

auburnimg.jpg

Limited Slip

Eaton

govloc.jpg

Gov-Loc

7.625 28 spline 3.23 and up only

Call...
Limited Quanities Available

Diferential Kit

diffkit.jpg

Includes side gears,
spider gears,washers,
cross shaft and lock screw

Cross Shaft and Lockscrew

crossshaftscrew.jpg

Open Bare
Case


opencasebare.jpg


Axle Shaft

axleshaft.jpg

Click for application list
...Call for information for non
listed applications or custom lengths...

Axle Bearings and Seals

axlebrgseal.jpg

K&L Unlimited 800-662-9103

HOME T-CASE DRIVESHAFT DIFFERENTIAL MANUAL TRANS ABOUT US